Description :
EM100Pro is DediProg Serial Flash Emulator based on RAM memory in order to offer the best update performances. This advanced tool has been designed in close cooperation with the Serial Flash suppliers to emulate the behaviors of all the market Serial Flash and also the next generation Serial Flash. | Densities | 512Kb | 1Mb | 2Mb | 4Mb | 8Mb | 16Mb | 32Mb | 64Mb | 128Mb | Erase + Program + verify | SPI Flash | 3s | 4s | 6s | 12s | 18s | 25s | 40s | 90s | 190s | EM100Pro | 3s | 3s | 3s | 3s | 3s | 3s | 3s | 3s | 3s |
“save 1 hour each day during development” Features :
Emulate all the market Serial Flash in one click Support upto 256Mb SPI flash emulation Support Dual IO & Quard IO Support Dual flashes emulation Update code in less than 3 seconds High speed SD card for standalone SPI trace data collection.(optional) Unlimited SPI signals trace SPI Hyper terminal to display debug messages from your application firmware to your host PC SPI Hyper terminal bidirectional communication to control your application firmware from your Host PC as a debugger Graphic User interface, Command Line or DLL to develop your own interface (on demand) USB powered & palm size Support Windows 2003 and above & Support both 32 bit or 64 bit OS SPI Flash Emulation interface: SPI Bus trace Interface: SPI Hyper terminal interface: · Hardware :
The EM100Pro has two 2.54mm pitch males connectors of: - 2*2 for the Reset and Trig signals - 2*10 for the Emulation signals
EM100pro is designed with ISP header, through an appropriate connector, users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status.Please refer to Table 1 for the EM100pro 2x10 header pin out. DediProg also provides the EM100pro ISP Cable which is used to connect theEM100pro programmer to the 2X52.54mm ISP Pin Header on board, please refer to Table 2 for theEM100pro ISP Cable 2x5pin out. Table 1: EM100pro ISP Header Pin Out (2x10),(2x2) 1 | Hold2 | CS2 | 2 | 3 | CS1 | Vcc | 4 | 5 | MISO | Hold1 | 6 | 7 | Wp1 | CLK | 8 | 9 | GND | MOSI | 10 | 11 | 3.3V | Wp2 | 12 | 13 | CTRL | NC | 14 | 15 | CTRL | 3.3V | 16 | 17 | CTRL | CTRL | 18 | 19 | GND | CTRL | 20 | 1
| GND | Reset | 2 | 3 | GND | Trig | 4 |
Table 2: ISP Cable Connector Pin Out (2x5) 1 | Hold2 | CS2 | 2 | 3 | CS1 | Vcc | 4 | 5 | MISO | Hold1 | 6 | 7 | Wp1 | CLK | 8 | 9 | GND | MOSI | 10 |
Contents :
• 1 x EM100Pro • 1 x USB 2.0 cable • 1 x 2.54mm 2x10 to 2.54mm 2x5 cable • 1 x 1.27mm 2x4 to 1.27mm 2x4 cable • 1 x 1.27mm 2x8 to 1.27mm 2x8 cable • 1 x 2.54mm 2x10 to 1.27mm 2x4/2x8 SO connection adaptor • 1 x 12cm EM100Pro split cable • 1 x EM100Pro DIP cable • 4 x 1.27mm 2x8 SMT male header (10.3mm) • 4 x 1.27mm 2x4 SMT male header (7.9mm) • 4 x 1.27mm 2x4 SMT male header (10.3mm) • 1 x 15cm single wire with Dupond header • 1 x EM100Pro Reference Flash Adaptor (SO8W) • 1 x EM100Pro Reference Flash Adaptor (SO16W) • 1 x Grabber Clip • Software and User Manual in CD ROM Benefits :
· Minutes becomes seconds for SPI Flash code update (3 seconds to update 256Mb SPI Flash) · Save up to 1 hours every days for your development and reduce your time to market Debug efficiently your application through the available SPI bus with our SPI Trace, SPI Trigger, SPI Hyper Terminal for debug messages Develop your own application debugger via our bidirectional SPI Hyper terminal and |