LabTool-T400 Turbo Flash Gang Programmer

LabTool-T400 Option 100

Features

· Support 3.3V to 1.2V flash memory chip in VCC and I/O without low voltage converter.

· Flash chip support up to 128G bit.

· Extremely high speed: it blank check a 64M bit flash chip in 1.6 seconds, program the STM28W640CT (4 word programming algorithm) within 11.5 seconds, verify within 3.2 seconds.

· USB interface: support USB 1.1 or 2.0

· One PC can connect up to 16 unit Labtool-T400 to perform Asynchronous programming

· Device insertion /continuity check before programming.

· Target quantity and Max failure rate alarm.

· Supports Windows 98SE / ME / 2000 / XP / Vista(32bit) / 7(32bit / 64bit)

· 1 year warranty

Introduction

· LabTool-T400 Turbo Flash Gang Programmer is four sockets PC-based Gang Programmer. It features four independent isolated modules, extremely high speed in writing flash memory chip. It supports 3.3V, 2.7V, 1.8V and 1.2V chip in both VCC and I/O without low voltage converter and handles 8/16/32 bit flash chip in different package through adapter modules, up to 128Gb flash can be support. The LabTool-T400 is an ideal programmer for customers in GSM, 3G Mobile, PDA, Internet router and others.

Unbeatable programming speed and throughput

· The LabTool-T400 has build in Compact Flash Card (CF) on board that reduce the massive data transfer between the PC and LabTool-T400 .The LabTool-T400 performance reach the speed limitation of the chips in its spec. No other gang programmer today and future can beat the speed of the LabTool-T400.

LabTool-T400 performance ( PC with P4 1.3G 128M RAM)

3.3V to 1.2V chip in VCC and I/O support

· The LabTool-T400 use the 90nm FPGA chip in hardware design, it can handle the chip from 3.3V to 1.2V in both VCC and I/O without need special low voltage converter circuit. This new technology fulfils customer's need and makes customer's investment fully protected.

High density chip support

· The LabTool-T400 has reserved the growth potential in chip's density. It covers 8/16 bit flash today and future's 32 bit flash chip. Its I/O pin driver can cover flash with Max 128G bit in density. This growth potential protected customer's investment without purchasing a new generation programmer over a decade in future.

Expansion through USB Hub and configure as a Multi-station Asynchronous Gang Programmer

· The LabTool-T400 interface with PC through USB interface, which support USB 1.1 and 2.0. If customer needs more units in production, just purchase extra LabTool-T400 and connect those LabTool-T400 through USB Hub, up to 256 LabTool-T400 can be attached to one PC. Recommend with 8-16 unit LabTool-T400 control by one PC to avoid performance decrease. Such configuration has significantly reduces the cost per station with low initial purchase cost and growth potential in future.

Adapter modules with ID

· The LabTool-T400 adapter module has independent ID. After inserting the module in the LabTool-T400, the system will detect the module's ID and compare the corresponding adapter modules with the chip select in software. This future prevents the wrong adapter module insert or wrong chip selection in operation.

Specification

Device support

· Flash memory: include NOR , NAND, EEPROM and other flash technology

· Device data width: 8, 16 and 32 bit

· Max flash density support: 512Mb with 128M byte Compact Flash Card install on board (standard offer), can be extend to 128Gb with exchange higher density Compact Flash Card on system hardware.

File format

· Binary, Intel Hex, Intel Ext Hex, Motorola S, HP64000 ABS, Straight Hex

Interface to PC

· Accept USB 1.1 or USB 2.0

PC system requirements

· Operating system: Windows 98SE/Me/2000 or Windows XP

· Processor: Pentium and above

· Memory: 256M and above

· Hard Disk: over 100M free space

· CD ROM driver

· Interface: USB 1.1 or 2.0 interface

General

· Power adapter: 65W AC 100-240/47-63HZ Auto Switch.

· Out put: DC (12V/3A, 5V/6A)

· Operation temp: 5 to 45 degree C

· Safety: CE&LVD certified

· Shipment Weight: 5.0 Kg without modules.

Download the most update LabTool-T400 software for a trial.

LabTool-T400 All device list.

窗体顶端

Information Request Form

Select the items that apply, and then let us know how to contact you.

Send product literature
Have a salesperson contact me

窗体底端

For more information, please contact:

Advantech Equipment Corporation
Fl. 7, No. 98, Ming-Chuan Road, Shing-Tien City, Taipei, Taiwan, R.O.C.
Tel: 886-2-2218-2325
FAX: 886-2-2218-2435

LabTool-T400 Turbo Flash Gang Programmer

LabTool-T400 Option 100

Features

· Support 3.3V to 1.2V flash memory chip in VCC and I/O without low voltage converter.

· Flash chip support up to 128G bit.

· Extremely high speed: it blank check a 64M bit flash chip in 1.6 seconds, program the STM28W640CT (4 word programming algorithm) within 11.5 seconds, verify within 3.2 seconds.

· USB interface: support USB 1.1 or 2.0

· One PC can connect up to 16 unit Labtool-T400 to perform Asynchronous programming

· Device insertion /continuity check before programming.

· Target quantity and Max failure rate alarm.

· Supports Windows 98SE / ME / 2000 / XP / Vista(32bit) / 7(32bit / 64bit)

· 1 year warranty

Introduction

· LabTool-T400 Turbo Flash Gang Programmer is four sockets PC-based Gang Programmer. It features four independent isolated modules, extremely high speed in writing flash memory chip. It supports 3.3V, 2.7V, 1.8V and 1.2V chip in both VCC and I/O without low voltage converter and handles 8/16/32 bit flash chip in different package through adapter modules, up to 128Gb flash can be support. The LabTool-T400 is an ideal programmer for customers in GSM, 3G Mobile, PDA, Internet router and others.

Unbeatable programming speed and throughput

· The LabTool-T400 has build in Compact Flash Card (CF) on board that reduce the massive data transfer between the PC and LabTool-T400 .The LabTool-T400 performance reach the speed limitation of the chips in its spec. No other gang programmer today and future can beat the speed of the LabTool-T400.

LabTool-T400 performance ( PC with P4 1.3G 128M RAM)

3.3V to 1.2V chip in VCC and I/O support

· The LabTool-T400 use the 90nm FPGA chip in hardware design, it can handle the chip from 3.3V to 1.2V in both VCC and I/O without need special low voltage converter circuit. This new technology fulfils customer's need and makes customer's investment fully protected.

High density chip support

· The LabTool-T400 has reserved the growth potential in chip's density. It covers 8/16 bit flash today and future's 32 bit flash chip. Its I/O pin driver can cover flash with Max 128G bit in density. This growth potential protected customer's investment without purchasing a new generation programmer over a decade in future.

Expansion through USB Hub and configure as a Multi-station Asynchronous Gang Programmer

· The LabTool-T400 interface with PC through USB interface, which support USB 1.1 and 2.0. If customer needs more units in production, just purchase extra LabTool-T400 and connect those LabTool-T400 through USB Hub, up to 256 LabTool-T400 can be attached to one PC. Recommend with 8-16 unit LabTool-T400 control by one PC to avoid performance decrease. Such configuration has significantly reduces the cost per station with low initial purchase cost and growth potential in future.

Adapter modules with ID

· The LabTool-T400 adapter module has independent ID. After inserting the module in the LabTool-T400, the system will detect the module's ID and compare the corresponding adapter modules with the chip select in software. This future prevents the wrong adapter module insert or wrong chip selection in operation.

Specification

Device support

· Flash memory: include NOR , NAND, EEPROM and other flash technology

· Device data width: 8, 16 and 32 bit

· Max flash density support: 512Mb with 128M byte Compact Flash Card install on board (standard offer), can be extend to 128Gb with exchange higher density Compact Flash Card on system hardware.

File format

· Binary, Intel Hex, Intel Ext Hex, Motorola S, HP64000 ABS, Straight Hex

Interface to PC

· Accept USB 1.1 or USB 2.0

PC system requirements

· Operating system: Windows 98SE/Me/2000 or Windows XP

· Processor: Pentium and above

· Memory: 256M and above

· Hard Disk: over 100M free space

· CD ROM driver

· Interface: USB 1.1 or 2.0 interface

General

· Power adapter: 65W AC 100-240/47-63HZ Auto Switch.

· Out put: DC (12V/3A, 5V/6A)

· Operation temp: 5 to 45 degree C

· Safety: CE&LVD certified

· Shipment Weight: 5.0 Kg without modules.

Download the most update LabTool-T400 software for a trial.

LabTool-T400 All device list.